Ascend Archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: (ASCEND) Accepting incoming connections from a Cisco?
Hello,
the RADIUS-user has to look like the following.
user Password = "test"
User-Service = Framed-User,
Framed-Protocol = PPP,
Ascend-IF-Netmask = 255.255.255.252,
Ascend-PPP-Address = you're ascend's interface ip address,
Ascend-Remote-Addr = Cisco's interface ip address,
Ascend-Route-IP = Route-IP-Yes,
Ascend-Metric = 2,
Ascend-Idle-Limit = 60
I tried this with a cisco 25xx and it worked.
Attention, you're chap username is the name of you ascend.
Greetings,
Robert
Date sent: Wed, 8 Jul 1998 05:05:37 -0400 (EDT)
From: Jason Nealis <nealis@babylon.erols.com>
To: Dave Carrigan <Dave.Carrigan@iplenergy.com>
Copies to: Ascend Mailing List <ascend-users@max.bungi.com>
Subject: Re: (ASCEND) Accepting incoming connections from a Cisco?
>
> Dave,
>
> Try having the user run some basic debug on his cisco, This should
> help you isolate the problem, The debug you would be interested in
> are as follows:
>
> debug ppp authentication
> debug isdn events
>
>
> Also, What type of Cisco is it? I have some basic setup configs for
> 2500 series routers that may also help.
>
> Jason Nealis
> Director Internet Operations / Network Access
> Erols Internet (An RCN Company)
>
>
>
> On Tue, 7 Jul 1998, Dave Carrigan wrote:
>
> > Hi, we have a Max 4048 running 5.0Ap11 that we use for general dialin
> > and router to router connections. Because we use Radius and SecurID,
> > we're set up to use PAP authentication (Ethernet->Answer->PPP
> > Options->Recv Auth=PAP). We have one client who wants to connect to us
> > with a cisco router. Unlike all of our other connections, the client
> > wants to use numbered interfaces on his cisco. I added an entry to the
> > radius file that looks like
> >
> > remote-rtr Password="xxxxxx"
> > Ascend-PPP-Address = 199.33.161.84,
> > Ascend-IF-Netmask = 255.255.255.192
> >
> > The problem is that the remote cisco dials and connects, but doesn't go
> > any further, and eventually disconnects. My syslog shows entries like
> >
> > Jul 7 05:27:28 erie.iplenergy.com ASCEND: call 63 CL 0K c=185 p=10
> > Jul 7 07:22:58 erie.iplenergy.com ASCEND: call 68 CL 0K c=185 p=77
> >
> > The docs say that this means the progress was either "Call is up" or
> > "LCP is in ACK Sent state". They don't say what cause code 185 means.
> > Does anybody have any suggestions as to where I should be looking next?
> >
> > --
> > Dave Carrigan (Dave.Carrigan@iplenergy.com)
> > Sr. Technical Analyst, Technology Services
> > Interprovincial Pipe Line Inc.
> >
> >
> >
> > ++ Ascend Users Mailing List ++
> > To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
> > To get FAQ'd: <http://www.nealis.net/ascend/faq>
> >
>
> ++ Ascend Users Mailing List ++
> To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
> To get FAQ'd: <http://www.nealis.net/ascend/faq>
>
Robert Koruna <robert.koruna@tiwag.co.at>
-----------------------------------------
TIWAG-Tiroler Wasserkraftwerke AG
Abteilung IT-UE
Eduard Wallnoefer-Platz-2
A 6010-Innsbruck
Tel.: +43 / (0)512 / 506 - 2772
Fax: +43 / (0)512 / 506 - 2670
-----------------------------------------
++ Ascend Users Mailing List ++
To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd: <http://www.nealis.net/ascend/faq>
References: