Ascend Archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
(ASCEND) 6.0.0 for the MAX family
6.0.0 for the MAX family has been given to support and manufacturing. This
release contains the following:
New features:
* BRI interface supports new analog encoding parameter
* Support for 64K and 56K calls with R2 signaling
* Israeli R2 signaling
* Danish switch type added
* MAX CH CNT upper limit specific to platform
* B-Channel preference when MP+ or BACP adds bandwidth
* BACP/BAP PPP protocol IDs match IETF
* TACACS+ server retry attempts
* Set Cause Code for ISDN DISCONNECT
* ISDN Pre-T310 Timer
* Enable data-service functionality for the MAX 4002 and MAX 4004
with AIM cards installed
* Raw TCP connection enabled
* TCP modem connections can be disabled
* User-definable TCP connection retry timeout
* IDSL voice call support
* Loopback support for IDSL card (BRI/LT)
* MAX supports new CSLIP Auto Detect parameter
* More information provided for SLIP connections
* Multilink or MP+ call now can span multiple MAX units
* Updated Microsoft Callback Control Protocol support
* MAXDial/IP support for immediate modem call restriction
* Support added for multiple host selection
* Limiting terminal server access per user
* User-configurable call blocking after failed connection attempt
* Specifying Shared Profiles per Connection Profile
* Terminal server users can be forced to use unique profiles
* CR-LF characters act as a single CR in terminal server
* DNIS support for TCP-CLEAR, X25/PAD, and X25/T3POS calls
* RADVision extensions to V.25bis for DNIS
* Enhanced support for T1/PRI conversion
* Enhanced support for outbound modem connections
* PRI number plan in outgoing AIM/BONDING and PPP calls
* PRI number plan in outgoing calls
* Enable NAT on MAX 1800 and 2000
* DHCP services on the MAX 1800 and 2000
* Show DHCP command added to terminal-server
* Alphanumeric IP pool names
* Removing routes to a host when the connection is down
* Local DNS host address table option added
* UDP Queue Control
* Specifying the metric and preference for offline WAN connections
* Specifying an OSPF ASE preference
* Specifying the OSPF type of pool advertisement
* Support for OSPF NSSAs (RFC 1587)
* Advertise static routes as OSPF internal LSAs
* Multicast default route
* Configurable multicast group membership timeout
* NetWare SAP Home Server Proxy
* SPX spoofing added for IPX
* New Answer profile option for dial-in NetWare clients
* Support for IPX without defining an IPX server
* ATMP attributes in RADIUS accounting
* RADIUS refers to filter and firewall policies defined in local profile
* NAS-Port-Type added to RADIUS Accounting records
* RADIUS Accounting checkpoint feature
* NACK option for Local Profiles First parameter
* Format of RADIUS NAS-Port attribute modified for the MAX
* Call-logging feature
* AppleTalk configurable from RADIUS
* RADIUS Accounting ATMP Notification
* Specifying preferences for routes configured in RADIUS
* SecurID authentication for ARA (AppleTalk Remote Access) clients using
RADIUS/LOGOUT
* MAX returns to primary RADIUS server after fixed time
* New RADIUS attributes enable call routing to PPTP
* RADIUS now recognizes packet types 33 and 34
* RADIUS Accounting-Request packets show whether accounting is enabled or
disabled
* Configuring Data Over Voice Bearer Service (DOVBS) in RADIUS
* New parameter for generating a second accounting Start record
* New RADIUS and terminal server support for Point to Point Tunneling
Protocol (PPTP)
* RADIUS support for IPX call and data filters
* Modem ID added to RADIUS Accounting Stop Records
* RADIUS now follows NI-2 PRI spec for outgoing calls
* SNMP can enable/disable/quiesce T1/PRI links
* Enable and Disable individual modem using SNMP
* SNMP write security disabled by default
* SNMP can help find which device a call is logged into
* SNMP "get" now retrieves MPP session statistics
* SNMP can monitor WAN lines and channels
* SNMP can obtain active call status
* SNMP system reset
* SNMP can detect concurrent sessions
* ASCEND MIB now includes modem status objects
* SNMP RFC 1398 Ethernet-like MIB (dot3) support added
* Set system clock through SNMP
* Terminating user sessions using SNMP
* Ascend MIB change supports counters for total and current calls
* Firewall Control Protocol managed by SNMP
* SNMP request authentication added
* Initiating RADIUS updates using SNMP
* SNMP sysConfigTftpStatus object reports more states
* SNMP now reports reasons for last reset
* Layer 2 Tunnel Protocol (L2TP) support added
* Maximum number of ATMP Tunnel sessions can be set
* ATMP inactivity timer
* Support for Finger remote user information protocol (RFC 1288)
* Terminal server show users command added
* Data rates reported to syslog
* Receive and transmit rates now reported
* Syslog enhancements
* Syslog messages generated when Security profile activated
* Configure port for Syslog messages
* Defender authentication enhancements
* RLOGIN enhanced -l option
* TFTP checks for compatibility of downloaded files
* Cexample now uses a session server key
* T1-CSU Status window added to the MAX 2000
* New 56K digital modem cards
* Disable modem capability added for MAX 1800 and MAX 2000
* 56k Modem Numbering
* Ability to select between V.34 and K56Flex modulation
* X.25 T3POS support
* X.25 over the D channel
* X.29 Reselection PAD message support
* Answer Profile for X25/PAD terminal server users
* Specifying X.3 parameters in an X.25 PAD Connection profile
* X.25/IP inactivity timer supported
* New X.25 user facilities parameters added
* Personal Handy Phone Service (PHS) support (Japan only)
* RADIUS bootup server supported for ZGR subaddresses and answer numbers
* ZGR answer numbers obtained from RADIUS
* ZGR subaddresses obtained from RADIUS
* DTPT encapsulation for T-Online PPP sessions
* PRI-PRI switching for T-Online
* AppleTalk routing added
* Defender authentication added for AppleTalk Remote Access Protocol (ARAP)
* Dial-in PPP support for AppleTalk
* SecurID authentication for AppleTalk Remote Access (ARA) users
* Enable data-service calls for the Multiband MAX 1800, 2000, and 4000
* Suppress the display of the second T1 line on the Multiband MAX 2000
* Suppress the T1-CSU and Serial WAN menus for the Multiband MAX 1800,
4002, and 4004
* Suppress the T1-CSU and Serial WAN menus for the Multiband MAX 2000
* Multiband simulation restricts MAX functionality
* Multiband only option added
* Megahertz CC1336 and XJ1336 modems available with MAX 200Plus
* USR Courier V.Everything modem available with MAX 200Plus
* Support for Xircom 33.6 PC Card modems
* Support for Hayes Optima 33.6 PC Card (PCMCIA) modems
* New modems supported on the MAX 200Plus
* Support for Practical Peripherals 33.6 V.34+Fax PC Card modems
* Support for Practical Peripherals 33.6 PC Card modem with EZ-Port
* Support for the Hayes Optima 33.6 PC Card modem with EZjack
* Support for Hayes Optima 288 V.34+Fax PC Card modems (Australia)
* Flashing CD lights indicate problems with modems
Corrections:
TR 918 Two MP connections to MAX caused second system to
reboot first.
TR 1070 Australian SPCs were not working correctly on the MAX 4000 E1.
TR 1168 Bad negotiation of MRRU hung Cisco or Yamaha routers
TR 1246 Connection problems between MAX and NT4.0.
TR 1269 Users showed connection to a MAX but were not
actually active.
TR 1270 Reduced incidence of type 1 disconnect records.
TR 1310 snmpset on radAcctCurrentServerFlag failure.
TR 1330 RADIUS truncates the "SD_CLIENT: name" field
to 5 characters.
TR 1374 SNMP variable callStatusIfIndex returned
wrong value
TR 1407 MPP subsequent channels caused IP address leak.
TR 1414 Static IPX routes defined in RADIUS not added
to routing table
TR 1421 Shared profiles were ignored.
TR 1422 PC dialing MAX received invalid IPX route.
TR 1455 MAX 1800 wouldn't dial port-to-port using
AIM/6 slot cards.
TR 1459 P130 - CSU wouldn't sync if signal was less
than -7.5db
TR 1490 IfType for Serial WAN incorrectly recorded for
Frame Relay
TR 1510 Closing Immediate Telnet session cleared
call before telnet disconnected.
TR 1546 MAX 4004 occasionally reset with fatal error 29.
TR 1561 RADIUS dial-out routes did not work.
TR 1562 Aview 1.1 coredumped.
TR 1579 MAX 4000 T1 reset when MP Stack was enabled.
TR 1584 IPX SAP tables not properly propagated
TR 1620 X.25/PAD and TCP-Clear connection couldn't be made.
TR 1624 After upgrade, the third T1 on a MAX 4000 did not
recover from a Yellow Alarm
TR 1631 Aview back panel was not operating as documented.
TR 1632 Coldstart message was not reported in RADIUS Accounting.
TR 1647 MAX BRI slot card B channel stays in the "r" state
with Switch Type=Japan.
TR 1653 Fatal error on MAX when ISDN hardware showed active
but wasn't.
TR 1664 When CLID failed, call was not answered.
TR 1667 MAX 4000 received a Fatal Warning 104.
TR 1684 Inactivity timer not started for CLID authentication call.
TR 1691 MAX Call Duration could not be disabled once value was set.
TR 1716 TNT didn't form OSPF adjacencies with the MAX 4000.
TR 1732 Nailed/MPP connections didn't establish switched link
consistently.
TR 1734 PBX-T1 was not functioning with Data Call option installed.
TR 1737 Large SNMP PDU size.
TR 1773 Ascend unit failed to connect BRI channels that
appeared to be stuck in ringing state.
TR 1775 M1800 didn't disconnect first call before callback.
TR 1783 RADIUS: CLID with dynamic IP and callback didn't work.
TR 1818 Terminal server "show calls" command did not
display phone number.
TR 1826 Local profiles didn't work when unit configured
with DEFENDER.
TR 1859 MAXDial/IP was not working in 5.0A or 5.0Ap1 (E1).
TR 1861 X.25/IP broken for more than two local profiles.
TR 1878 With PAP-TOKEN-CHAP, second channel couldn't be
brought up.
TR 1880 Third prompt setting was not echoing correctly.
TR 1925 Routes sometimes incorrectly went to WANIDLE.
TR 1930 MAX 4000 was supporting only 9 concurrent users.
TR 2002 IP pool leak problem using MP and JapaneseTA.
TR 2023 MAX started sending compressed data to an NT
workstation even though compression was not negotiated.
TR 2028 MAX 4000: Under a heavy load, calls were not connecting
completely.
TR 2046 Call Duration was not working on a MAX 4004.
TR 2054 Occasionally, the MAX 200Plus could not bring up a
4-channel call to another MAX.
TR 2055 Unconfigured MAX 200Plus invisible to Console.
TR 2072 Data filter wasn't applied for RADIUS-authenticated
user if Answer Defaults=Yes.
TR 2085 The MAX did not always support two incoming calls on
the same BRI line from a 5ESS switch.
TR 2092 MAX 2000: Boot hung with V110 card installed.
TR 2096 MAX 4000: Poisoning of dial-out routes didn't work
correctly.
TR 2100 FR MTU/MRU calculation caused fragmentation problems.
TR 2135 Disabling or enabling one BRI line affected the other
BRI lines in unit.
TR 2145 MAX 1800 BRI lines did not come up after reset
TR 2153 MAX 4000 units running the TCP Modem feature
would crash when a TCP modem user entered an incorrect
password.
TR 2154 MAX 4000 running ARA, gave warnings (indexes 145 and 175)
and reset with a Fatal Error 2.
TR 2158 On a MAX 4000, the Net/T1 menu would occasionally
appear as "Not Available".
TR 2163 callActiveTable not valid unless a call was active
TR 2198 SNMP reported MAX 2000 product ID incorrectly
TR 2236 The MAX could not dial out from a PRI GTD 5 switch.
TR 2242 MAX 1800 were resetting with Fatal Error 19
TR 2245 The MAX did not recognize Telnet-Break on V.34 and
K56flex calls.
TR 2256 MAX 4000 units running T1-PRI conversion, could not place
outbound calls. New parameters have been introduced to
fix this problem.
TR 2287 On an incremental software version, 64K channels could
not be added to MP+ calls.
TR 2292 SNMP reported incorrect number of modems
TR 2293 Users could not disable modems on MAX 1800 or MAX 2000
TR 2309 TCP statistics for TCP-Clear calls were not being generated
TR 2328 MAX did not operate correctly with GTE GDT5 switch and
Siemens switch.
TR 2345 Password authentication did not work with BONDING calls.
TR 2357 MAX 4000 sent wrong value for trap 12
TR 2398 The MAX units were resetting with an FE2.
TR 2426 MAX units with the combined E1/R2 and K56 hash codes
enabled did not answer modem calls.
TR 2429 MAX responded to FINGER only once.
TR 2438 If a mobile node tried to FTP files over an ATMP
connection, the transfer would occasionally fail.
TR 2439 MAX reset - FE 1 - when simultaneous clear TCP session
users dial in.
TR 2446 MAX4000 with PHS did not reject voice incoming call
via PRI
TR 2466 RADIUS Accounting Start packet missing IP address.
TR 2470 MAX 200Plus: USR Sportster modem connection issues
TR 2475 MAX sent menu prompt twice at Terminal Server Login.
TR 2478 Cannot get second channel into bind in a MAX stack
using CHAP-TOKEN-PAP.
TR 2533 MAX units running bridging in a MAX stack reset with a
FE 2 or 29 and warning 175.
TR 2538 The MAX 2000 E1 model did not interpret NET 5 charging
information.
TR 2540 MSN client username was not understood by the MAX
TR 2584 MAX 4000 reset-FE1-5.0Ap18.
TR 2589 RADIUS accounting and authentication used a single
sequence of packet IDs.
TR 2599 Incorrect username for RADIUS accounting was
generated when Immed Svc was defined.
TR 2605 MAX 4000 reset-FE8-5.0Ap18.
TR 2648 RADIUS accounting problems with Auth-Authentic=local
TR 2658 MAX did not add network route for static IP user defined
in RADIUS.
TR 2659 "Use Answer As Default=Yes" caused PPP sessions to fail
for Tserv login users. (RADIUS accounting problems)
TR 2690 Fatal Error 2 after running 10 days.
TR 2692 MAX CBCP did not call back to synchronous user.
TR 2693 Fatal Error 1 in 5.0Ai23
TR 2738 Fatal Error 1 on digital modem slot card failure
TR 2747 MAX 200Plus created broadcast storm when routing IPX enabled
TR 2771 Could not write ssnStatusValidFlag and ssnActiveValidFlag
in the Session MIB using SNMP
TR 2772 SNMP did not report all callStatusGroup
TR 2781 First channel of an MP+ bundle dropped on when line
utilization falls
TR 2785 MAX 2000 reboots with FE 1 on SNMP query
TR 2794 SNMP needed three states: Failed, Succeeded,
Transferred.
TR 2804 MAX reset with FE 2 and Warning 175 every few days.
TR 2820 MAX was not sending CLID/DNIS accounting request to RADIUS
when caller hung up
TR 2821 MAX accounting log did not record start of 2nd channel
of MP+ call when stacked
TR 2830 MAX 1800 fatal error 2
TR 2843 TCP-Clear options not working in Connection profile
TR 2863 PRI number plan in outgoing call using RADIUS
TR 2864 PRI number plan in outgoing call using local Connection
profile
TR 2865 PRI number plan in outgoing call using local
Dial Plan profile
TR 2874 MAX did not callback user if CBCP Mode=User Num and
Use Trunk Grps=No
TR 2889 MAX did not add addresses assigned to CBCP users to
its routing table
TR 2902 Increase immediate Telnet and Rlogin performance and
maximum # of sessions
TR 2931 In 5.0Ap36 MAX 1800 reset with fatal error 8
TR 2939 Multicast routes in routing table caused HP Openview
to display incorrect MAX icon
TR 2952 MAX rejected incoming calls
TR 2954 MAX sent CBCP callback request to non-CBCP users
TR 2956 MAX 1800 did not respond to incoming BRI call
TR 2971 For Raw-TCP sessions, logout message not fully
displayed
TR 2980 SNMP did not report OSPF state correctly
TR 2993 RADIUS Framed IP route pointed to the Ethernet
interface instead of a WAN port interface
TR 3000 Some MAX loads too large for flash memory
TR 3012 Syslog not reporting end-of-call information
TR 3013 Syslog syntax fixed
TR 3015 MAX 1800 provided wrong number for second channel
of MPP call
TR 3059 MAX 2000 would reset with Fatal Error 1 and
no fatal error log on large OSPF networks
TR 250002 DHCP option needed for NAT.
TR 250008 Using MAXDial, M4000 used SPEECH Bearer Service for
outgoing modem calls.
TR 250017 MAX 1800 could not activate a 1TR6 NT from a Info 0 state
TR 250026 ELSA Microlink x.75 TA session was disconnected and hung.
TR 250038 MAX 4000 reset - Fatal Error 2.
TR 250046 PPTP with RADIUS connected only one end-point.
TR 250066 DHCP missing from MAX 2000 and 4000.
TR 250074 The MAX would not disconnect a user after an X.25/PAD
autocall was finished.
TR 250088 During an X.25 session, the MAX would not always
send the entire X.25 packet
TR 250098 MAX and Pipeline units overwrote static IPX routes with
SAP updates
TR 250103 Frame relay fragmentation did not work with ATMP
TR 250110 MAX inserted additional bytes on backup frame relay PVC.
TR 250127 MAX 4000 reset with FE 2.
TR 250134 Pipeline took several seconds to connect to MAX
TR 250153 MAX did not send Call User Data on first X.25/PAD call
TR 250157 MAX, with stacking enabled, would reject calls with
names longer than 11 characters
TR 250158 MAX answering TCP-Clear calls would require reset
after 3 or 4 days
TR 250169 MAX 2000 did not correctly interpret V.120 Reject frame
TR 250185 During PPTP session RADIUS accounting packets not
logged correctly
TR 250199 MAX not answering modem calls after receiving ISDN call
* Appletalk routing not supported over Frame Relay links.
* MAX reports non-SNMP version 1 PDU as authentication trap.
* Good V.34 modems occasionally fail POST.
* DHCP request failed if host specified an IP address not in list.
* SDSL fixes for startup reliability, temperature adaptation, serial swap.
Known issues:
* When you bring up a call using the IPXPING command, Answer
appears in the IPX Route Table as an entry under the Origin
column. When the call is disconnected, the table returns to normal.
* The MAX does not send IPX RIP Response packets for a
PPP-encapsulated dialup connection
* In countries which support A-law encoding, 56k Modem
handshake fails when a user dials out using either the
MAX terminal server or the DeskDial client.
* When dialing a busy number, terminal server outdial modems
do not report BUSY. The MAX detects the busy signal and goes
on-hook before its modem receives the busy signal. The MAX
reports Cause Code 17 in the message log, and modems disconnect,
displaying NO CARRIER. This might be a problem for users or
scripts that require a modem to report BUSY.
* When Stacking is enabled, PAP-TOKEN-CHAP is not supported.
* Data filters are not supported when used in conjunction with
Microsoft's CallBack Control Protocol (CBCP)
Rockwell code version:
* Release 6.0.0 supports Rockwell K56flex code version 1.160t.
Kevin
++ Ascend Users Mailing List ++
To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd: <http://www.nealis.net/ascend/faq>
Follow-Ups: