(ASCEND) 7.0.22 for Max

[Matt Holdrege <matt@ascend.com>]

The TAOS 7.0.22 software for the MAX family is now available from customer
service. This release contains the following:

Corrections
TR 2879: In Terminal Server menu mode, unavailable selections could be chosen.
TR 3844: An Appletalk enabled MAX 4002 issued warning 175.
TR 3940: Telnet to a MAX 6000 using a broadcast address did not work on an
ethernet connection.
TR 4210: MAX sent ATMP RIP when "ATMP RIP=Off" for Home Agent(HA).
TR 4303: Direct SecureID authentication was not supported, and dial-in
users to a MAX received a Remote Authentication Timeout message.
TR 4390: MAX supporting permanent ISDN connections occasionally logged
Warning 145 messages.
TR 4417: When a Windows 98 user entered an incorrect ID or Password during
CHAP authentication, they did not receive an authentication failure message.
TR 4508: One voice call failed when a MAX placed two simultaneous outgoing
voice calls on a T1 or T1-PBX line.
TR 4514: A MAX 800 with four analog pcmcia modems did not complete an MPP
connection.
TR 4556: IPX & IP routing between Windows 95/98/NT laptops to MAX 200Plus
or MAX 800 caused Windows 95/98/NT system to reboot or generate a system
unstable message.
TR 4615: A MAX 4004 PRI ISDN reset with FE1.
TR 4694: A MAX 6000 issued warning 179 then rebooted.
TR 4757: Max sent Navis Access logging transmissions to radius accounting.
TR 4764: After an upgrade from 5.0Ap38 to 7.0.4, a MAX 4048 issued an
FE1and then reset.
TR 4868: MAX 4000 supporting OSPF reset issuing a warnings 175, 200, and 201.
TR 4905: A MAX 6000 reset with FE 1 after issuing a warning 179.
TR 4926: A MAX 6000 incorrectly reported Ascend-Num-In-Multilink whenever a
session timed out.
TR 250298: TCP host and dial-in MAX reported inauthentic accounting values
for TCP clear connections.
TR 258608: Data call from a Multiband VSX to a MAX 2000 Host/Dual call was
cleared with ISDN code 16.
TR 258646: L2TP and AAC authentication failed when a MAX 4000 used single
RADIUS server.
TR 258738: During call setup, a MAX 4000 did not allow for network-provided
CLID authentication.
TR 258766: MAX failed to create PPTP tunnels after being up for extended
periods of time.
TR 258770: CLID authentication and Navis RADIUS filters were incompatible.
TR 258772: SourceIP Check did not work on some spoofed packets.
TR 258776: A MAX 4000 reset with an FE29 as a point to point tunnel was built.
TR 258787: On a Max 200Plus, the Filter-ID setting did not function.
TR 258791: Without referring to a secondary home agent, a MAX terminated a
tunnel registration process when a primary home agent was unavailable.
TR 258821: While functioning as a Home Agent, a MAX 4000 generated, and did
not clear, unused ATMP tunnels.
TR 1000105: IPX network traffic was incorrectly received and stored in the
Max routing table from permanent virtual circuits when Route IPX = No.
TR 1000150: A MAX 6000 issued warning 561 and FE18 then reset.
TR 1000186: MAX E1 displayed a Red Alarm LED.
TR 1000192: MAX 4000 E1/R2 CLID response was incorrectly handled.

Conexant (formerly Rockwell) firmware versions
Digital modem modules Conexant versions
K56-8, -12, and -16 2.098
V.34 Modem-12 1.610G24
V.34 Modem-8 1.610G19

Notices of discontinuance (post 7.0.x)
Software support for v.34 slot cards
Support for MAX 4000 product family

++ Ascend Users Mailing List ++
To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd:	<http://www.nealis.net/ascend/faq>