Re: (ASCEND) TCP-IP "stalling" or stops routing on max6k

["Rahul Verma" <rahulverma@pinkline.net>]

i want to make my computer as LAN/WAN router , so i need two adapter card
one is ethernet card , other should be WAN interface card , but i am unable
to find such product ,, can anyone tell me ..about this ...


----- Original Message -----
From: <maxed_out_user@hotmail.com>
To: <ascend-users@max.bungi.com>
Sent: Wednesday, June 21, 2000 4:14 AM
Subject: Re: (ASCEND) TCP-IP "stalling" or stops routing on max6k


> The next time the problem occurs to a particular user, the things I
> would do to troubleshoot this are:
>
> Drop into terminal server and issue these commands:
>
> show users
> show ip route
> show arp
>
> You can get the IP address of the problem user and then from the routing
> table, you can see if the route is correct for that user.  If you want
> to see if the user's ping packets are making it to the Max, you have
> turn on this command in Diagnostics mode:
>
> wandsess <username> 64
>
> For example, if the username (as appears in "show users") is 'testuser',
> then the command would be...
>
> wandsess testuser 64
>
> To turn it off, issue this command...
>
> wandsess testuser 0
>
> This will isolate packets only coming from this user (not everyone like
> the 'wandisp' command would).  Have the user ping something beyond the
> Max and see if you see any RECV packets.  This might help isolate where
> the fault is.
>
> Oh, and regarding your other question...
>
> How does one access this type of info (seen posted to this list):
> > MODEMDRV-3/0: _postTask: expected response not received
>
> ...it just appears by itself (unsolicited) upon boot up of the Max only
> when the modem card fails to come up for some reason.  When you first go
> into Diagnostics mode, you'll see this, but after that the buffer in
> Diagnostics mode gets cleared so you don't see it again unless the Max
> is rebooted and the modem card fails to come up again.
>
>
>
> Hi all,
> I have gleaned much information from this list in the past.  I hope
> someone out there might be familiar with this problem:
>
> Analog/v90/v34 user connects fine and at good line speed.
> They surf for a while then the connection locks up.
> They cant ping beyond their gateway (the MAX 6096) so they lose
> DNS resolution, and all other IP sources.
> Connection is still up, it is not a disconnect problem.
> They just are not passing/routing the data.
>
> Here are specifics:
> Max6096 and 4 PRIs
> load tck.m60
> happend with ver 7.0.22 & 7.2.4 (running 7.2.4 now)
>
> I have my vendor support looking at a syslog capture from the weekend
> but they dont see anything wrong yet.
>
> How does one access this type of info (seen posted to this list):
> > MODEMDRV-3/0: _postTask: expected response not received
> > MODEMDRV-3/15: _postTask: expected response not received
> Is it at the diag prompt?  How to get it?
> Any suggestions on diagnosing the problem?
>
> Any help greatly appreciated.  Lucent support told me to go to ver 8.
> Based on other 8.x postings, I dont want to do that.
>
> Thanks,
> Scott Boggs
>
> ++ Ascend Users Mailing List ++
> To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
> To get FAQ'd: <http://www.nealis.net/ascend/faq>
>

++ Ascend Users Mailing List ++
To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd:	<http://www.nealis.net/ascend/faq>