RE: (ASCEND) Error on new TNT Ethernet Card

["Joe Max" <max_and_tnt@hotmail.com>]

Kevin,
Are you sure that's an Ethernet card and not a T1 card?
What do you get when you do 'show'?
As far as I know, there are three possible Ethernet cards for the TNT:
  - the old card that had 4 10-baseT ports plus an optional 100-baseT (aka, 
4ether-card or 4/1ether-card)
  - the second generation card, that has 3 10-baseT ports + 1 100-baseT port 
(aka, 4ether2-card)
  - the fast card for voip, with a single 10/100-baseT port and a dongle 
(aka, ether3-card)

-J

>From: "Kevin McKee" <Kevin@northwestnt.com>
>To: "Peter Lalor" <plalor@infoasis.com>, <ascend-users@max.bungi.com>
>Subject: RE: (ASCEND) Error on new TNT Ethernet Card
>Date: Wed, 14 Jun 2000 11:27:55 -0700
>
>My card is just an 8 port Ethernet card.  I've got two of them in the
>box, and the first one has been working fine.  The second card is in a
>perpetual RESET state, even after I reloaded the tntrel.tar file and
>rebooted a  few times.  When the card is 'up' I get the following
>message:
>    LOG error, Shelf 1, Slot 17, Time:  00:49:52--
>    Slot 1/3, timeout failure code=0 during  TIMEOUT
>When I take it down ( slot -d 1 3 ), the error message goes  away.  I'm
>running software 8.0.2
>
>Can I assume this is a bad card?
>
>The last time I called Ascend tech support, it took a full WEEK before
>they  called me back.  And their knowledge level wasn't very high.  I'm
>guessing I'll get a quicker answer from the people on this mailing list.
>
>Thanks,
>Kevin
>
>	-----Original Message-----
>	From: Peter Lalor
>	Sent: Wed 6/14/2000 9:07 AM
>	To: ascend-users@max.bungi.com
>	Cc: Kevin McKee
>	Subject: Re: (ASCEND) Error on new TNT Ethernet  Card
>
>
>
>	>From: "Kevin McKee"  <Kevin@northwestnt.com>
>	>
>	>I might be missing something  here, but I've  got a new
>Ethernet-8 card
>	>in our TNT, and I can't  get it to work.  I keep  getting the
>following
>	>error:
>	>
>	>LOG error, Shelf 1, Slot 17,  Time:  00:49:52--
>	>   Slot 1/3, timeout failure code=0  during TIMEOUT
>	>
>	>I already have a functioning card of the  same type in the box.
>A
>	>'show' gives it's status as  'RESET'
>
>	I don't know what an "Ethernet-8" card is, but are you running
>a
>	version of code that supports it? Do you have the image for
>that
>	particular card loaded? Do dircode for a list of what card
>images  are
>	loaded. You may need to load a new one for that  card.
>	--
>
>	Peter  Lalor           Infoasis
>	plalor@infoasis.com   http://www.infoasis.com/
>
>	"Where's  my burrito?" -- Homer
>
>
>++ Ascend Users Mailing List ++
>To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
>To get FAQ'd:	<http://www.nealis.net/ascend/faq>

________________________________________________________________________
Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com

++ Ascend Users Mailing List ++
To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd:	<http://www.nealis.net/ascend/faq>